A new surface modification technique for PET films is proposed. This technique, called VPI modification technique, is a combination of two processes: The first step involves the deposition of vinylphthalimide (VPI) on the PET film surfaces, followed by Ar plasma irradiation of the VPI-covered film surfaces. The VPI modification technique led to large increases in the N/C atom ratio on the PET film surfaces. On the VPI-modified PET film surface, a new N_ls peak containing two components due to amide groups as well as imide groups appeared. The C_ls signal for the VPI-modified PET film surface also showed a new component due to ketone groups. These changes indicate that VPI reacted with the PET film surfaces to form nitrogen-containing groups. VPI modification made PET film surfaces hydrophilic. The VPI-modified film surfaces showed a decrease in water contact angle from 73 degrees to 48–56 degrees.

In conventional offset lithographic printing, it has been well established that the existence of a continuous layer of fountain solution (FS) on the surface of the non-image area is an essential condition to ensure correct operation of lithography. However, the mechanistic function of FS in preventing the ink from being transferred onto the non-image area has not been fully understood. Several major mechanistic interpretations can be found in the literature, which are based either on comparing of static works of adhesion and cohesion of ink and FS, or on the splitting of the 'weaker' FS layer. Although the latter becomes more accepted, direct experimental evidence is difficult to find in the literature. On the other hand, confusing information found in the literature showed that the ink-transfer (or non-transfer) observations reported in many case studies correlate well with simple comparisons of works of adhesion, cohesion and spreading data of ink/FS, ink/plate and FS/plate obtained under the static condition. These results, therefore, imply that, in explaining the function of FS in preventing ink transfer to the non-image area, the ink/FS interfacial adhesion failure would be the dominant mechanism. The work presented in this study covered two specific areas in order to address and better understand the responses of ink and FS layers and their interface to forces encountered during ink transfer. Firstly, an analysis of lithographic plates contaminated with a cationic polymer revealed that the violation of the ink non-transfer condition of the plate non-image area due to contamination could be predicted by traditional criteria of plate wetting and works of adhesion and cohesion. However, these traditional criteria cannot reliably predict the non-transfer condition of the ink on the clean non-image area that was covered by FS. Secondly, in some novel experiments conducted in this study using ice or Teflon as a substrate, the works of adhesion and cohesion were not able to predict ink transfer in most cases. Direct experimental evidence from this work revealed that splitting of the FS layer was involved in the prevention of ink transfer to the non-image areas, and that the thickness of the FS layer was critical in allowing the splitting to occur.

Oxygen plasma-treated quenched and annealed polypropylene (PP) films with different crystallinities were investigated to characterize the surface rearrangement behavior during aging using contact-angle measurements and X-ray photoelectron spectroscopy. Optimum plasma conditions were examined by varying the power, time and pressure. Less crystalline quenched PP showed a larger increase in water contact angle and a larger decrease of oxygen atomic concentration during aging than the more crystalline annealed PP, since the oxygen species, such as hydroxyl groups, introduced by oxygen plasma treatment, oriented towards or diffused faster into the bulk with lower crystallinity. The degree of crosslinking on the surface was enhanced after plasma treatment and, in addition to increased crystallinity, the crosslinked structure induced by plasma treatment restricted chain mobility and lowered the aging rate of the PP surface.

Poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) surfaces were exposed to vacuum UV (VUV) photo-oxidation downstream from Ar microwave plasma. The modified surfaces showed the following: (1) an improvement in wettability as observed by water contact angle measurements; (2) surface roughening; (3) defluorination of the surface; and (4) incorporation of oxygen as CF—O—CF₂, CF₂—O—CF₂ and CF—O—CF₃ moieties. With long treatment times, a cohesive failure of copper sputter-coated onto the modified surface occurred within the modified FEP and not at the Cu–FEP interface.

The current work incorporates a microscopic study of the effect of fiber orientation on the fiber wetting process and flow of liquid droplets along filter fibers when subjected to airflow and gravity forces. Glass filter fibers in various combinations were oriented at various angles within a plane defined by the airflow direction and were supplied with distilled water in aerosol form. The behavior and flow of the liquid collected by the fibers were observed and measured using a specially developed microscope cell, detailed in the paper. The experimental results were compared to a theoretical model developed to describe the behavior. The theory and experimental results showed good agreement. The developed theory allows an optimum angle to be determined for the internal filter fiber structure in the design of wet filters. A sensitivity analysis of the model was conducted to determine the most important parameters. This will aid design of wet filtration systems such that maximal self-cleaning can be accomplished with minimal water use.

Plasma treatment effectively alters the surface of textiles and reduces the need for using environmentally hazardous chemicals. Applications of the technology include enhancing wettability, adhesiveness of polymer surface, and anti-felting properties of wool fibers, as well as improving dyeing properties, and sterilization. Free radicals generated on the surface can induce further crosslinking or polymerization.

Surface modification of textile fibers using gas plasma is a useful tool in altering the wettability, adhesiveness, and dyeability of synthetic polymer-based textiles. Plasma treatment is also effective for biomedical applications such as sterilization. Antibacterial properties can be achieved by subsequent grafting.

The surface energy of coating layers influences their final properties such as their ability to repel or absorb fluids. Recent work has shown that the substrate, due to absorption, can alter the surface chemistry of the top coating layer. However, the influence of substrate properties on coating surface energies is not reported in the literature.Three coatings, based on a pigment and a latex binder, are applied on three different substrates that differ in terms of absorption properties. The three coatings were also modified with a soluble polymer. Contact angle measurements of three different probe fluids were measured. These contact angles were used to estimate the polar, dispersive, and total surface energy of the coating layers. Surface energies were also determined for the latex and pigments.The contact angles and surface energies of the latex films and pigments agree with the expected results. Most of the results for the coating layers agree with the reported surface chemistry of these coatings. Large pigment systems on absorbent substrates have a high contact angle and low surface energy. These results agree with the expected results based on the surface chemistry reported in past work. The results for the fine pigment system had low contact angles and high surface energies and did not agree with the expected results. The contact angles may be influenced by the surface roughness of the coatings or the expected surface energy of a heterogeneous surface may not be a simple function of the surface composition.

Emission spectroscopy was applied to observe the reaction process of poly (ethylene terephthalate) (PET) in an oxygen (O2) plasma generated by a microwave discharge. As the PET was exposed in the O2 plasma flow, light emitted from the PET surface was monitored. In the diagnosis measurement, several emission peaks assigned to the Hα atomic line at 652 nm, Hβ at 486 nm, OH (2Σ→2Π) transition near 244–343 nm and CO (b3 Σ→a3 Σ) near 283–370 nm were observed and measured at various discharge times. These results indicated that after the plasma etching, the PET sample was decomposed by the oxygen plasma reaction, and then, hydrogen abstraction and carbon oxidation processes. We also observed the time profile of oxygen atom, as the atom-emission intensity at 777 nm was monitored. As Hβ atomic and OH molecule lines appeared in the presence of PET, the O atom intensity was significantly reduced. In the surface analysis on Fourier transform infrared and x-ray photoelectron spectroscopy measurements, it was found that for the PET surface treated by O2 plasma containing excited atomic oxygen species, ester bands were broken and carbonization formed on the PET surface.

In the gas flame treatment of low surface free energy (SE) substrates, such as high-density polyethylene (HDPE), problems might arise from under or over flaming, oxygen concentration differences in and around of the flame, etc. Consequently, in printing applications, the possible variation of induced SE existing on the surface, could cause distortion on printed letters. In this research, a new method based on the wetting and spreading phenomena was developed to display and study details of the SE variation on HDPE flame treated substrates. It was an easy and quick method. Results showed good agreements with previous works done on the flame treatment characteristics. The optimal flaming was achieved, while the substrate surface had been positioned about 10 to 12 mm below the tip of the flame's blue part. Also when the flaming speed had been controlled about 80 mm/s. Results from the adhesion strength test supported the optimum situations found previously by others. It was hoped that this new method could also be capable of estimating the critical SE of solid surfaces in future works.

Polyolefins such as polyethylene, polypropylene and their copolymers have excellent bulk physical/chemical properties, are inexpensive and easy to process. Yet they have not gained considerable importance as speciality materials due to their inert surface. Polyethylene in particular holds a unique status due to its excellent manufacturer- and user-friendly properties. Thus, special surface properties, which polyethylene does not possess, such as printability, hydrophilicity, roughness, lubricity, selective permeability and adhesion of micro-organisms, underscore the need for tailoring the surface of this valuable commodity polymer. The present article reviews some of the existing and emerging techniques of surface modification and characterisation of polyethylene. Surface modification of polymers, polyethylene in particular, has been extensively studied for decades using conventional tools. Although some of these techniques are still in use, they suffer from distinct shortcomings. During the last two decades, different means of surface modification have been thoroughly explored. The increasing expectancy for smart materials in daily life has, of late, sharply influenced research in the area of surface modification. Technologies that involve surface engineering to convert inexpensive materials into valuable finished goods have become even more important in the present scenario. In this review article we have attempted to broadly address almost all conventional and modern techniques for the surface modification of different physical forms and chemical compositions of polyethylene. This article will hopefully stimulate further research in this area and result in the development of polyolefins with multi-functional and responsive surfaces, which would ultimately lead to the commodities of polyolefins with smart surfaces.

Neumann−Good's parallel strip model (J. Colloid Interface Sci. 1972, 38, 341) was used to analyze the contact angle hysteresis for a liquid on a heterogeneous surface composed of alternatively aligned horizontal apolar (θ = 70°) and polar (θ = 0°) strips. The critical size of the strip width, below which the contact angle hysteresis disappears, was determined on the basis of the analysis of the activation energy for wetting to be from 6 to 12 nm. This calculated value of the critical strip size is 1 order of magnitude smaller than that of 0.1 μm, which has been commonly considered as the limit of heterogeneity size causing the appearance of the contact angle hysteresis.

In the present paper, the following topics are reviewed in detail: (a) the available adhesives, as well as their recent advances, (b) thermodynamic factors affecting the surface pretreatments including adhesion theories, wettability, surface energy, (c) bonding mechanisms in the adhesive joints, (d) surface pretreatment methods for the adhesively bonded joints, and as well as their recent advances, and (e) combined effects of surface pretreatments and environmental conditions on the joint durability and performance. Surface pretreatment is, perhaps, the most important process step governing the quality of an adhesively bonded joint. An adhesive is defined as a polymeric substance with viscoelastic behavior, capable of holding adherends together by surface attachment to produce a joint with a high shear strength. Adhesive bonding is the most suitable method of joining both for metallic and non-metallic structures where strength, stiffness and fatigue life must be maximized at a minimum weight. Polymeric adhesives may be used to join a large variety of materials combinations including metal-metal, metal-plastic, metal-composite, composite-composite, plastic-plastic, metal-ceramic systems. Wetting and adhesion are also studied in some detail in the present paper since the successful surface pretreatments of the adherends for the short- and long-term durability and performance of the adhesive joints mostly depend on these factors. Wetting of the adherends by the adhesive is critical to the formation of secondary bonds in the adsorption theory. It has been theoretically verified that for complete wetting (i.e., for a contact angle equal to zero), the surface energy of the adhesive must be lower than the surface energy of the adherend. Therefore, the primary objective of a surface pretreatment is to increase the surface energy of the adherend as much as possible. The influence of surface pretreatment and aging conditions on the short- and long-term strength of adhesive bonds should be taken into account for durability design. Some form of substrate pretreatment is always necessary to achieve a satisfactory level of long-term bond strength. In order to improve the performance of adhesive bonds, the adherends surfaces (i.e., metallic or non-metallic) are generally pretretead using the (a) physical, (b) mechanical, (c) chemical, (d) photochemical, (e) thermal, or (e) plasma method. Almost all pretreatment methods do bring some degree of change in surface roughness but mechanical surface pretreatment such as grit-blasting is usually considered as one of the most effective methods to control the desired level of surface roughness and joint strength. Moreover, the overall effect of mechanical surface treatment is not limited to the removal of contamination or to an increase in surface area. This also relates to changes in the surface chemistry of adherends and to inherent drawbacks of surface roughness, such as void formations and reduced wetting. Suitable surface pretreatment increases the bond strength by altering the substrate surface in a number of ways including (a) increasing surface tension by producing a surface free from contaminants (i.e., surface contamination may cause insufficient wetting by the adhesive in the liquid state for the creating of a durable bond) or removal of the weak cohesion layer or of the pollution present at the surface, (b) increasing surface roughness on changing surface chemistry and producing of a macro/microscopically rough surface, (c) production of a fresh stable oxide layer, and (d) introducing suitable chemical composition of the oxide, and (e) introduction of new or an increased number of chemical functions. All these parameters can contribute to an improvement of the wettability and/or of the adhesive properties of the surface.

The surface energy parameters of polycaprolactone (PCL) were determined at 160 and 180°C from its interfacial tensions with probe polymers. The probe polymers were polystyrene (PS) and poly(methyl methacrylate) (PMMA). This method is based on the well-known relationship between blend interfacial tension and polymer surface energy parameters, and requires the use of at least two probe polymers, whose surface energy parameters at the temperature of interest have been independently determined. It also requires direct measurement of blend interfacial tension at the high temperatures of interest. The interfacial tensions were obtained from direct measurements by the imbedded fiber retraction method. The following results were obtained: (a) γ^P (polar component) values for PCL was within the range reported using other methods, (b) γ^D (dispersion component) values for PCL decreased with increasing temperature, consistent with expectations and (c) γ^D values for PCL were on the high end, but still within the rather broad range of reported values.

In this paper, we report and discuss the results of the surface treatment, using an atmospheric pressure dielectric barrier discharge (DBD), of selected polymer films which have no bonded oxygen in their intrinsic structures. Contact angle, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) data are presented with respect to post-treatment characterisation and the dependence of these outcomes on the salient processing variables: energy dissipated, exposure duration and inter-electrode gap. Under the treatment conditions used, remarkably uniform treatment and markedly stable modified surface properties result from the test surfaces exposed to the discharge, even at transit speeds simulating those associated with continuous on-line processing. The DBD system thus described, provides chemically mild and mechanically non-destructive means of altering surface properties, targeting improved surface characteristics and potentially better application performance.

Properties like adhesion of inkjet prints on unporous media are strongly determined by wetting characteristics of ink on media. In contrast to solvent based inks for UV-curable inkjet-systems the ink is not allowed to equilibrate on surfaces because the film is cured within a very short timeframe after jetting. Therefore the static surface tension is not able to characterise the ink-media interaction before the ink curing process is initiated. In a time-scale of milliseconds the dynamic surface tension measured with the maximum pressure bubble method can be used to describe the dynamic processes of ink on unporous media. In this paper we present a study of dynamic surface tension of mono-, di-, and trifunctional acrylates in order to evaluate the effect of molecular weight, structure and the behavior of mixtures on the resulting dynamic surface tension in UV-curable inkjet inks.

Commercial polymers in thin film form were used for modification by atmospheric RF plasma. The influence of the plasma treatments using Ar and Ar+O₂ on surface energy, morphology and chemical structure of the films was investigated. It was revealed that both modifications caused surface activation of the polymer film, but they obeyed different mechanisms enhancing polymer wettability. First, surface graphitization due to argon sputtering caused hydrogen to free the surface and then reacts with oxygen in the air. Second, surface oxidation is connected with the functional group formation. The reactions of Ti with the polymer led to the simultaneous formation of TiCl₂, TiC, Ti-oxide and they contributed to film adhesion. In comparison with Ar, the mixed Ar+O₂ RF plasma treatment was a more timesaving process and had more influences on surface activation and film adhesion.

To prevent the loss of fiber strength, ultrahigh-molecular-weight polyethylene (UHMWPE) fibers were treated with an ultraviolet radiation technique combined with a corona-discharge treatment. The physical and chemical changes in the fiber surface were examined with scanning electron microscopy and Fourier transform infrared/attenuated total reflectance. The gel contents of the fibers were measured by a standard device. The mechanical properties of the treated fibers and the interfacial adhesion properties of UHMWPE-fiber-reinforced vinyl ester resin composites were investigated with tensile testing. After 20 min or so of ultraviolet radiation based on 6-kW corona treatment, the T-peel strength of the treated UHMWPE-fiber composite was one to two times greater than that of the as-received UHMWPE-fiber composite, whereas the tensile strength of the treated UHMWPE fibers was still up to 3.5 GPa. The integrated mechanical properties of the treated UHMWPE fibers were also optimum. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 463–472, 2004
https://onlinelibrary.wiley.com/doi/10.1002/polb.10727

In this paper, we report and discuss the results of the surface treatment, using an atmospheric pressure dielectric barrier discharge (DBD), of selected polymer films which have no bonded oxygen in their intrinsic structures. Contact angle, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) data are presented with respect to post-treatment characterisation and the dependence of these outcomes on the salient processing variables: energy dissipated, exposure duration and inter-electrode gap. Under the treatment conditions used, remarkably uniform treatment and markedly stable modified surface properties result from the test surfaces exposed to the discharge, even at transit speeds simulating those associated with continuous on-line processing. The DBD system thus described, provides chemically mild and mechanically non-destructive means of altering surface properties, targeting improved surface characteristics and potentially better application performance.

In recent work, we found that the stability of the negative corona charge in radio frequency plasma treated polytetrafluoroethylene (PTFE) films (18 µm thickness) strongly depends on the plasma sources, the exposure time and the condition of the film in the plasma, i.e. the film orientation on the holder and whether the film is one-sided metallized or non-metallized, as well as the film side for corona charged. Using Fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy, we conclude that two factors affect the negative charge stability: oxide formed on the surface and positive charges trapped in the film. The oxides serve to retain the negative corona charges and the plasma-generated positive charges recombine with the negative corona charges and cause the corona charge discharge after heating.

The surface characteristics of ethylene-vinyl acetate (EVA) were modified by argon, air, and oxygen plasma at atmospheric pressure. The surface energies of the EVA were evaluated by contact angles according to a sessile-drop method and adhesion energy (G(IC)) was estimated by a 180 degrees peel test with polyurethane (PU). After the plasma treatments, the surface free energies (or specific polar component) of the EVA increased about five times compared to that of virgin EVA. The adhesion between the EVA and the PU is significantly improved by the plasma treatment. Especially, Ar/air/O(2) plasma treatment increases G(IC) of EVA/PU up to about 600% compared to that of the sample using virgin EVA.

The purpose of this study was to develop a standard methodology for measuring the surface free energy (SFE), and its component parts, of dental biomaterials. The contact angle of each of four samples of two materials--low density polyethylene and poly(methyl methacrylate)--was measured three times in each of six liquids (1-bromonaphthalene, diiodomethane, ethylene glycol, formamide, glycerol and distilled water). Critical surface tension estimates were obtained from Zisman plots. Data were then analyzed by the least-squares method to estimate the components of SFE. Estimates were also made for each of 12 liquid triplets, and by maximum likelihood and Bayesian analyses. The use of liquid triplets could yield misleading estimates of the components of SFE. A testing protocol is suggested in which multiple test liquids are used, and multiple methods of statistical analyses employed. SFE is important, in that high SFE is desirable when adhesion is required, but undesirable if plaque resistance is needed. Methodology that avoids some of the limitations of existing studies has been proposed.

The acid-base approach to the calculation of solid surface free energy and liquid-liquid interfacial tensions is a practical example of application of correlation analysis, and thus it is an approximate approach. In these limits, and provided that wide and well-obtained sets of contact angles or interfacial tension data are used for their computation, surface tension components can be considered as material properties. Although their numerical value depends on the characteristics of the chosen reference material, their chemical meaning is independent on the selected scale. Contact angles contain accessible information about intermolecular forces; using surface tension component (STC) acid-base theory, one can extract this information only making very careful use of the mathematical apparatus of correlation analysis. The specific mathematical methods used to obtain these results are illustrated by using as an example a base of data obtained by the supporters of the equation-of-state theory (EQS). The achievements are appreciably good and the agreement between STC and EQS is discussed.

This paper follows the “defense” of the Good-van Oss-Chaudhury (GvOC) acid-base approach made in Part I and carries out a detailed analysis of the Zisman critical surface energy and, mainly, of the Neumann equation-of-state (EQS) theory. The analysis is made on both a “practical” and a theoretical basis, trying to highlight the acceptable fitting results of axisymmetric drop shape analysis (ADSA) methods and their independence of the assumed thermodynamic foundations of EQS. Some new and original criticisms of the EQS approach are raised and it is shown that other purely semiempirical models, represented by different fitting equations with the same number of parameters, can represent the data measured by ADSA method with the same goodness as EQS. The equation of state appears as one of many semiempirical approaches for the evaluation of surface free energy of solids. Independent of the previous analysis, the criteria used in ADSA measurements are evaluated and some comments made on them.

This study concerns the surface and adhesive properties of isotactic polypropylene (iPP) modified by an electric discharge plasma and affected by long-term hydrophobic recovery of the polymer surface after modification. The investigations were focused on the change in polarity of the modified polymer expressed by the polar fraction as well as on the decrease in the surface free energy, its polar component and mechanical work of adhesion (A _m) to polyvinyl acetate. A _m of modified iPP to polyvinyl acetate as a function of polar fraction can be described by a mathematical formula. It has been confirmed that the most intensive decrease in the surface and adhesive properties investigated is produced by the long-term hydrophobic recovery of the polymer appears in the course of the first 30 days after its modification. During subsequent aging the process of polymer hydrophobic recovery proceeds more slowly. It has been found that the value of surface and adhesive properties of iPP as well as the dynamics of the decrease in these properties during hydrophobic recovery of the surface after modification is, in the main, dependent on the iPP crystallinity.

The polymers PET, PA6, PVDF, HD-PE, and PP are activated by a commercially available plasma jet system at atmospheric pressure to improve adhesive bondability. The adhesion properties of the activated surfaces are evaluated by lap shear tests. The results are correlated with the surface properties that are investigated by XPS, AFM, and contact angle measurements. In addition the influence of operational parameters of the plasma treatment is studied. The activated samples exhibit a substantially increased bonding strength. The improvement can be related to an increase of oxygen concentration, and to changes of the topology of the substrate surface induced by the thermal component of the plasma. The most influential parameters in the plasma treatment are the distance between substrate and nozzle exit and the treatment time.

This work deals with the study of the durability, in a hot/wet environment, of structural adhesively bonded polyetherimide (PEI) assemblies used in power electronics packaging technology. An overall approach is proposed, for which the epoxy joint-PEI substrates assembly on the one hand, and the adhesive system components (substrate surface and bulk adhesive) on the other hand, are studied separately with different analytical techniques. The first part of this work was devoted to the substrate surface state and to its modification using a cold plasma treatment of the PEI surface. Then for chosen parameters (power, duration) contact angle measurements indicated an increased surface tension resulting from surface decontamination (removal of release agent and carbon contaminants) and from the creation of polar species, such as esters or carboxylic acid groups, on the PEI surface (XPS analyses). The second part of this study concerned the bulk adhesive ageing in an ethylene glycol-water solution at 70°C. Mass uptake measurements versus time showed the liquid diffusion in the bulk adhesive associated with a microscopic damage of the epoxy system. An overall plasticizing of the adhesive with a considerable decay of the α-transition temperature of one of the two adhesive epoxy-amine networks (TGDDM-BAPP) was also highlighted using rheometry. However, in these ageing conditions, the adhesive glassy modulus decreases slighty because of the thermomechanical stability of the other epoxy network. In the third part, the asymmetric wedge test showed the beneficial effect of the cold plasma treatment on the epoxy/PEI interface durability in the aggressive medium.

A new process, the Non Anchor Coating Extrusion Laminating Process for producing an extrusion laminated film without any chemical primer, was investigated. Good adhesive properties were obtained by combining an ozone treatment of a molten polyethylene (LDPE) web and an activation treatment of the polyamide (ONy) substrate film. The adhesion mechanism induced by the new process was studied by FT-IR, ESCA and extraction of unreacted polyamide from the laminated samples. The peel strength between the ONy and LDPE laminated films produced with this process was greater than that for laminated film made with a conventional lamination process using anchor coating agents. A model of the adhesive mechanism is proposed. Hydrogen and covalent bonds through oxygenated functional groups are responsible for the enhanced adhesion.

To many people, plasma is a laboratory curiosity or limited in scale. Few know that plasma is a commercial process used daily in the treatment of fabrics, non-woven webs and film. This paper reviews applications and processes used to modify materials up to 60 in. in width in a roll-to-roll plasma system. The applications are quite varied. Sometimes, the process is simply to change the surface energy, while at other times, far more sophisticated processes, such as plasma-enhanced chemical vapor deposition (PECVD) processes, are employed to provide a chemical barrier or alter the tribological properties. As will be seen in this review presentation, plasma is extremely versatile and applicable to high-volume web applications.